A Feral Sorcery moment

[DiLoco_DelEted]

There is actually a book called Feral Sorcery. The idea is to use your self reliance and creativity as driving factors of how to get ritual things done.
So today I had a feral sorcery moment.
Let me tell you, the biggest pain in the ass are using birthday candle tees, because two out of ten times you will have to throw the candle away because it snaps in half while trying to cram it into the tee. Then you have spell candles which dont fit on a tee, not do tapers. The only other candles I have are about a hundred white tealights.
So how oh how am I supposed to let a candle burn all the way (this may be dangerous with bubble gum, bubble gum can flame up and catch fire)?

1. Clay
2. Putty
3. Bubble gum thats used and dried

Clay is good but takes time to Harden. Putty is good but not as moldable as clay. Bubble gum can be used, bit how to use the gum or clay?
CVS: Front register Bubble Yum Tape roll
CVS: Office Supplies: Push pins for something else (Enochian Watchtower tablets), Mounting putty strips
CVS: School Supplies area: Clay bucket with molds and tools included.

So now what? How oh how will I fit these different circumference candles into a hole of that size, unlike tees, and how do I keep it deep enough yet firm enough to not snap candles in half upon entry?

Step 1: Recycle your used tealight candle
Take a steak knife, sewing needle, or tweezers, and either pull by the wick with one hand while firmly gripping the tin in the other hand, pull directly up in a quick motion. You may find this does not work. Fear not. Gently with a flat tip tool, pry a little the tin edge from the candle edge. Try to pluck the candle out or push it out from the bottom.
Readjust tin base to be flat, using a quarter a flat surface and pressure might do the trick.
Have some bubble gum, or get some putty or clay. I will try all three methods starting with gum.
While chewing your gum, get some candle oil, and oil the candle base. Wash and dry your hands.
With the used tealight block, turn upside down and remove wick assembly.
Place used wax in a collection tin to later make wax by recycling the old.
Place chewed gum, clay or putty in tin. Ideally fill tin halfway with any.
Place new candle flat in the gum/putty/clay
Allow to Harden. Carefully remove candle, the hole should remain in place as the gum hardens.

Step two: Use a suitable container to use clay with.
Gotta say, the tealight steps are pretty solid no matter the medium.

Step 3: Use mounting putty
Gotta say, the tealight steps are pretty solid no matter the medium.


Ideally, I would create several, in case you need candles at each quarter and one on the altar, etc.

 

[DiLoco_DelEted]

FWIW, clay is least likely to catch fire of the three, should the candle completely burn down to the base.
Adding some sort of liquid flame retardant on top of the candle base assembly with a mounted candle.

 

[DiLoco_DelEted]

https://imgur.com/a/y11rvcn

Please, Log in or Register to view URLs content!

 

[DiLoco_DelEted]

https://imgur.com/a/yWR7hf9

Please, Log in or Register to view URLs content!

 

[DiLoco_DelEted]

Added incense stick to the candle gum tin.
Will try the same with both mounting putty and clay in two separate tins.

By the way, not only can you recycle the wax, but the tins as well. In addition to using the tins for candle holders, you can flatten the tins to use as talismans for Jupiter related spirits.
Set the empty tin flat on a counter.
Using simple pressure with fingertips, fold four sections down and flatten best you can.
Set on other side and obtain a happier or suitable device to flatten tin.
Carefully flatten with the tool best you can. Even a fist can be used to flatten it if need be.
Turn around, and carefully draw an outer circle close to the edge.
Within the circle with a one point marker, draw the sigil.
Outside the circle write the letters of the name.
Consecrate as you would any talisman for Jupiter.

 

[DiLoco_DelEted]

Another Feral Sorcery moment: The magic Circle, Paper clasps, and belts.

I used to be in a certain Martial Art called To-Shin-Do. In their belt system, you have the four elements, then void and then black belt with a number of BB ranks. For each element, three belts are used: Solid with white stripe, solid, solid with black stripe. In black stripe belts you were eligible for testing into a new element.
Their elements go in this order: Earth, Water, Fire, Wind, Void, Black.
Earth belts: White solid, yellow solid, yellow-black.
Water belts: Blue-white, solid blue, blue-black.
Fire belts: Red-white, solid red, red-black.
Wind belts: Green-white, solid green. green-black.
Void belts: Brown-white, solid Brown, brown-black.
Black Belt: up to six ranks, highest is current Grandmaster of both Ninjitsu and To Shin Do.

I obtained up to my Red-White belt, and before solid Red had to drop classes due to money problems.
So, therefore at this time, I have seven belts total.
Each belt is about two feet long, and 2-3 inches high.

1 Obtain paper clasps, the black plastic clips with two silver finger clasps.
2 Take two belts, secure with clasp as each end.
3 Clasp all belts together until none are left, claps final two ends into a solid upright circle.
4 Using regular paper, tear into even strips equal to belt height.
5 Write characters of choice around belt circle. Perhaps not clasp final ends until finished with character etching and set upright on end and clasped together. Leaving a etches upright circle.

Im going to do this as soon as I obtain clasp clips.

 

[DiLoco_DelEted]

The method of putty with a tin for a candle holder:

https://imgur.com/a/KVlxRXn

Please, Log in or Register to view URLs content!

https://imgur.com/a/zUAgIXC

Please, Log in or Register to view URLs content!

Please, Log in or Register to view URLs content!